Car Repair<

How to Replace a Fuel Injector in a Chevy Impala

The Chevy Impala has a fuel injector that mixes fuel with air. This technology almost completely replaced carburetors in the late 1980s and its programmable firmware allows the same hardware to be used with different fuels. A fuel injector is only a nozzle and a valve; it still requires a pump to inject the fuel into the engine.



Difficulty:
Moderately ChallengingInstructionsThings You'll Need:
  • Fuel injector kit
  • Socket wrench set
  • Torque wrench
  1. Step 1

    Determine which fuel injector your Chevy Impala will need. This depends not only on the make and model, but also the engine size. The first generation of the Impala covers 1958 to 1961 and these models were available with 235 cubic inch (ci), 283ci, 348ci and 409ci engines. Second generation models made from 1962 to 1964 may have a 230ci, 283ci, 327ci or 409ci engine.

  2. Step 2

    Look at later generations of the Impala. The third generation was made from 1965 to 1970 and was offered with 250ci, 283ci, 307ci, 350ci, 396ci, 409ci and 427ci engines. The fourth generation Impala covers 1971 to 1976 and was available with 350ci, 400ci and 454ci engines.

  3. Step 3

    Check the engine sizes for more recent versions of the Impala. The fifth generation was made from 1977 to 1985 and may be equipped with 229ci, 231ci, 250ci, 267ci, 305ci, 350ci or a 350 diesel engine. The sixth generation of the Impala covers 1994 to 1996 and has a 5.7L engine.

  4. Step 4

    Examine the engine size for the latest models of the Chevy Impala. The seventh generation was made from 2000 to 2005 and is available with 3.4L and 3.8L (supercharged and non-supercharged) engines. The latest generation debuted in 2006 and may have a 3.5L, 3.9L or 5.3L engine.

  5. Step 5

    Disconnect the negative battery cable with a socket wrench and relieve the fuel system pressure. Remove the fuel injector sight shield with a socket wrench and disconnect the fuel send and return lines.

  6. Step 6

    Remove the fuel pressure regulator vacuum hose and ignition coil wires from the coil. Disconnect the electrical connectors from the fuel injectors. Remove the fuel rail mounting nuts with a socket wrench, release the retaining clips for the fuel injector and remove the fuel injectors. Discard the old O-rings.

  7. Step 7

    Install the new fuel injectors by reversing the removal procedure. Coat the new fuel injector O-rings with clean engine oil. Use a torque wrench to tighten the fuel rail mounting bolts to 7 foot pounds and torque the mounting nuts for the fuel injector sight shield to 27 inch pounds.

Car Repair Talk's forum.



Pre:How to Replace a Fuel Injector in a Plymouth Voyager   Next:How to Replace a Fuel Injector in a Chevy Corvette

  • How to Remove the Windshield Reservoir
  • How to Replace a Blower Motor in a 1998 Buick Regal LS
  • How to Change Motor Home Shocks
  • How to Clear Clogged Windshield Washers
  • How to Replace the Throttle Body in a Mitsubishi 3000GT
  • How to Install a New Steering Rack in a Chrysler Sebring
  • How to Replace the Thermostat in a 1998 BMW 323IC
  • How to Replace a Thermostat in a Lincoln Mark 8
  • Car Parts: Air Conditioning System / Body / Lighting and Signaling System

    OBD-Ⅱ Trouble Codes:OBD-Ⅱ Trouble Codes

    P0108 | P0135 | P0171 | P0174
    P0300 | P0320 | P0325
    P0401 | P0420 | P0430 | P0440 | P0441 | P0442 | P0455

    links:Car Logo / Autoi / Car Repair Talk's forum / Car Specifications